FreshSentry Water Treatment System (Chlorine free)
Our chlorine free FreshSentry Water Treatment System is consist of following elements:
1. an electrode chamber that can function as ionization and oxidation.
ionization provide copper ions to control water bactria against infections of Legionella, Without proper level of ion, the pool water may also gradually turn greenish. It is the algae that grows inside the pool. Technically, 0.4 ppm of copper is desired in the pool to keep the water clean and clear. Ionization process is achieved by our copper plate electrode inside the chamber.
upon opening the pool, or after freshly changed pool water, the copper level normally is low. we should manually switch to ionization mode to let the pool build up the copper level for about two or three days continously, until copper level reaches at least 0.3 ppm level. Then the system can be switched to automatic mode to enjoy worry free water system.
oxidation process is undergoing with or without copper ionization. It is recommended that FreshSentry should be always turned on as long as the water pump is running. It provides maximum sanitation with almost no cost. You pay less than 1 penny a day to operate FreshSentry for the elctricity energy cost.
2. a power set units that controls ionization and oxidation process automatically.
The control unit controls ionization and oxidation at the same time. The unit can be turned on/off from the panel with a LED indicator. There is also an ionization switch to allow manual/automatic ionizing. Ionization LED is on and off, controled by a switch. This control unit provides power for ionization and oxidation process. On the control unit panel, we also have a water hardness meter to monitor pool water hardness. It is a critical parameter for FreshSentry to work normally.
pure water is not a good conductor of the electricity. In order to maitain proper level of ionizing and/or oxidation, pool water need to be maintained to certain level of hardness. The harder it is, more calcium ions in the water, the more conductivity the water gets. Even for a standard chlorine pool, it is recommended that pool hardness should be kept to 200ppm to 400ppm level of Calcium, to avoid corrision of pool equipment. Most pool owners pay little attention to water hardness level. Because it does not directly related to water quality. Pool owners tend to overlook the importance of the pool water hardness.
But.it becomes a must to maitain water hardness to 300/400 ppmlevel, in order to make FreshSentry work properly, If the water is not hard enough, we should put in some calcium flaks (i.e. HardnessPlus) into the pool to raise the hardness of the water. Incorrect hardness will result poor water treatment. Because water hardness is so critical for FreshSentry to function normally, our front panel has a amper meter to display hardness level. Normally, the hardness should be around 0.3-0.4 amp, that is corresponding to about 300-400 PPM of calcium level.
3. Installation free setup
installation of FreshSentry is very easy. In order to be more friendly to general pool owners, we have developed a special model that requires no installation (patent in applying), Just hookup the power and drop in the electrode chamber into the pool water and you are ready to go! All in 5 minutes! It is surprisingly convenient for everyone to use.
4. Compare to other similar product in the market
a. no stain mess: If you have used other similar products in the market before, you might be frustrated by the stain that it generates that messes up the swimming pool. Our FreshSentry system is carefully designed to make sure that messy will never happen. You have one less worry when using our FreshSentry products. You can be resting sure that your pool will be always crystal clean.
b, more efficient and clean: Pool filter hides most debris and organic materials, that service as food for bacteria. Bacteria develops rapidly inside the pool filter. Other vendors install water treatment segment at pool return water pipe. Their system does no sanitation to the filter. Water thus always gets contaminated through the filter. Although oxidation will greatly reduce the level of bacteria, there are still a lot of left over bacteria surviving the oxidization. The net efficiency of the our competitions product is not high. The pool would be not clean as expected. However, our unique design of FreshSentry does oxidization at entry pipe point. No only our oxidization process takes longer time (water oxidizes from entry from pool to returning to pool), but also effectively oxidizes the filter. There is no blind spot of dirt because of our special architecture design. Our product is much more efficient than our competitions.
c. more portable and simple: Another great advantage of FreshSentry system is that it is much easier to install and operate, when comparing to products of other competitive vendors. We can sell product online and customers can put it to work themselves in about 15 minutes.
1. an electrode chamber that can function as ionization and oxidation.
ionization provide copper ions to control water bactria against infections of Legionella, Without proper level of ion, the pool water may also gradually turn greenish. It is the algae that grows inside the pool. Technically, 0.4 ppm of copper is desired in the pool to keep the water clean and clear. Ionization process is achieved by our copper plate electrode inside the chamber.
upon opening the pool, or after freshly changed pool water, the copper level normally is low. we should manually switch to ionization mode to let the pool build up the copper level for about two or three days continously, until copper level reaches at least 0.3 ppm level. Then the system can be switched to automatic mode to enjoy worry free water system.
oxidation process is undergoing with or without copper ionization. It is recommended that FreshSentry should be always turned on as long as the water pump is running. It provides maximum sanitation with almost no cost. You pay less than 1 penny a day to operate FreshSentry for the elctricity energy cost.
2. a power set units that controls ionization and oxidation process automatically.
The control unit controls ionization and oxidation at the same time. The unit can be turned on/off from the panel with a LED indicator. There is also an ionization switch to allow manual/automatic ionizing. Ionization LED is on and off, controled by a switch. This control unit provides power for ionization and oxidation process. On the control unit panel, we also have a water hardness meter to monitor pool water hardness. It is a critical parameter for FreshSentry to work normally.
pure water is not a good conductor of the electricity. In order to maitain proper level of ionizing and/or oxidation, pool water need to be maintained to certain level of hardness. The harder it is, more calcium ions in the water, the more conductivity the water gets. Even for a standard chlorine pool, it is recommended that pool hardness should be kept to 200ppm to 400ppm level of Calcium, to avoid corrision of pool equipment. Most pool owners pay little attention to water hardness level. Because it does not directly related to water quality. Pool owners tend to overlook the importance of the pool water hardness.
But.it becomes a must to maitain water hardness to 300/400 ppmlevel, in order to make FreshSentry work properly, If the water is not hard enough, we should put in some calcium flaks (i.e. HardnessPlus) into the pool to raise the hardness of the water. Incorrect hardness will result poor water treatment. Because water hardness is so critical for FreshSentry to function normally, our front panel has a amper meter to display hardness level. Normally, the hardness should be around 0.3-0.4 amp, that is corresponding to about 300-400 PPM of calcium level.
3. Installation free setup
installation of FreshSentry is very easy. In order to be more friendly to general pool owners, we have developed a special model that requires no installation (patent in applying), Just hookup the power and drop in the electrode chamber into the pool water and you are ready to go! All in 5 minutes! It is surprisingly convenient for everyone to use.
4. Compare to other similar product in the market
a. no stain mess: If you have used other similar products in the market before, you might be frustrated by the stain that it generates that messes up the swimming pool. Our FreshSentry system is carefully designed to make sure that messy will never happen. You have one less worry when using our FreshSentry products. You can be resting sure that your pool will be always crystal clean.
b, more efficient and clean: Pool filter hides most debris and organic materials, that service as food for bacteria. Bacteria develops rapidly inside the pool filter. Other vendors install water treatment segment at pool return water pipe. Their system does no sanitation to the filter. Water thus always gets contaminated through the filter. Although oxidation will greatly reduce the level of bacteria, there are still a lot of left over bacteria surviving the oxidization. The net efficiency of the our competitions product is not high. The pool would be not clean as expected. However, our unique design of FreshSentry does oxidization at entry pipe point. No only our oxidization process takes longer time (water oxidizes from entry from pool to returning to pool), but also effectively oxidizes the filter. There is no blind spot of dirt because of our special architecture design. Our product is much more efficient than our competitions.
c. more portable and simple: Another great advantage of FreshSentry system is that it is much easier to install and operate, when comparing to products of other competitive vendors. We can sell product online and customers can put it to work themselves in about 15 minutes.